Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
LiftMaster openers
Before
After
Before
After
Before
AfterAmarr Torsion Spring Replacement: The Carrollton Owner’s Guide
Amarr torsion spring replacement in Carrollton typically runs $180 to $340 installed, and we carry Amarr-compatible springs on the truck for same-day service in most cases. You’ll usually know the spring has failed before you ever confirm it visually: a loud bang from the garage that sounds like a firecracker, followed by a door that won’t lift more than a few inches. The spring sits above the closed door on a metal shaft, and when it breaks, that shaft spins and releases the stored tension all at once, which is the noise you heard.
We’re an independent garage door service company. We’re not affiliated with Amarr, but we stock and install torsion springs matched to Amarr’s specifications and we’ve replaced enough of them across Carrollton to know which models fail in predictable ways. The good news is that a broken spring is a known part, a known price range, and a known repair time, usually 45 to 90 minutes once we’re on site.
Which Amarr Models This Applies To
Amarr builds doors under several lines you’ll recognize: Lincoln, Olympus, Heritage, Classica, Hillcrest, and the builder-grade Stratford series. All of them use torsion spring systems, but the spring that fits a 16-by-7 Lincoln 2000 is not the spring that fits a 9-by-7 Stratford. Amarr, like most manufacturers, specs each door with a spring matched to the door’s weight, height, cable drum type, and track radius. That’s why a universal spring is never the right answer, even if it’s cheaper.
The most reliable way to identify your spring is to read the color code painted on the spring’s stationary cone or the wire tag if it’s still attached. Amarr and their spring suppliers use a color-and-wire-diameter system: a pair of red springs on one door is not the same as a pair of red springs on another, because the inner diameter, wire gauge, and coil count also matter. If the tag is gone or the paint is faded, we measure the wire diameter with a caliper, count the coils, and check the inside diameter before quoting anything. That measurement is what tells us the correct replacement, and it’s part of what you’re paying for.
On the OEM versus aftermarket question: Amarr’s springs are manufactured to their specifications, but the aftermarket springs we install from companies like SSC and DDM Garage Doors are often built to equal or higher cycle ratings. A cycle is one full open and close. Standard builder-grade springs are often rated for 10,000 cycles, which in Texas heat works out to roughly 7 to 9 years of normal use. We can install a higher-cycle spring for a modest upcharge, and we’ll show you the rating printed on the spring’s documentation.
Signs Your Amarr Torsion Spring Replacement Is Failing
Most owners don’t get a warning before a spring snaps. The break is sudden. But there are earlier signs that one side is wearing faster than the other, and they’re worth catching before the door jams halfway up while you’re late for work.
- A door that feels heavier than it used to. Torsion springs counterbalance the door’s full weight. As a spring loses tension through coil fatigue, the opener motor and your arm take up more of the load. If the door suddenly feels like it weighs twice as much, the spring is doing less than half its job.
- Visible gaps in a coil. When a spring begins to fail at a stress point, one or two coils separate from the rest before the full break. If you can see daylight through a coil gap on an intact-looking spring, that spring is in its final stage.
- Cables that look loose or sagging. The lift cables run down both sides of the door and stay taut because the spring system holds tension. If one cable is slack while the door is closed, the spring on that side has likely failed and left the cable with nothing to pull against.
- The door opens unevenly or binds on one side. A single broken spring on a two-spring door leaves the remaining spring pulling alone. The door starts to twist, the rollers bind in the track, and the opener works harder than it should. Left running this way, the opener can burn out its travel limit or strip a gear.
- A bang from the garage followed by the door refusing to open. That’s the definitive one. The spring breaks, the shaft spins, and the door either stays down or opens a few inches under opener force, then stops. If you heard the bang, stop pressing the opener button and check visually before anything else.
BeforeAfterReplacement Cost & What’s Included
A single Amarr-compatible torsion spring replacement in Carrollton runs $180 to $340 installed. Double-spring doors sit at the upper end of that range because both springs should be replaced at the same time, even when only one has failed. The two springs on a double-spring system wear at the same rate, and replacing one alone leaves the door unbalanced and shortens the life of the new spring.
The price you get from us is the price you pay. It’s quoted in writing before any work begins, and it includes the new spring or springs, the labor to install and wind them, a balance check on the full door, and adjustment of the cable tension on both sides. We also photograph the failed part before we touch it, and you get those photos along with the written scope and the invoice when we’re done. That’s Clause 4 of The Haven Standard, and it’s how we’ve worked since 2015.
Every torsion spring replacement we do carries our 365-Day Done Right Promise: if it’s not right, we make it right. No fine print, no prorating, no phone tree.
DIY or Call Us?
Replacing a torsion spring is one of the few garage door jobs we actively tell homeowners not to attempt. The spring is wound under hundreds of pounds of torque, and the winding bars, if they slip or the wrong bar is used, can break bone or worse. This is not a “watch a YouTube video and try it” repair. The risk isn’t the money you’d save, it’s the injury you can’t undo.
What you can safely do: check whether the spring has visible damage, note the color code or measure the wire diameter if you have calipers, take a photo of the setup, and call us. We’ll tell you over the phone whether it’s a single or double spring, what the price range is for your door size, and give you a written quote before the technician starts work. That’s the order Marcus Deller runs every job by: name the part, quote the price, do the work, in that order. Call (817) 527-9864 and we’ll walk you through it.
Frequently Asked Questions
Standard Amarr torsion springs typically last 7 to 10 years in the Carrollton climate, with the heat and humidity of North Texas summers shortening the life of lower-cycle springs. A spring rated for 10,000 cycles on a door that opens four times a day will last about 7 years. If your opener, cable drums, and spring rating are all matched properly, you can expect the full lifespan; if the spring was undersized at installation, it can fail in as little as 3 years.
Call (817) 527-9864 and we’ll help you figure out what you have and what a proper replacement should be.
No. A broken torsion spring cannot be repaired, welded, or re-tensioned safely. The metal has failed permanently at the stress point, and any attempt to patch it creates a spring that can snap again without warning. Replacement is the only option, and it’s a straightforward parts-and-labor job.
We’ll quote you the exact replacement price before we do anything else.
Most torsion spring replacements take 45 to 90 minutes once the technician starts. That includes removing the old springs, installing and winding the new ones, checking the balance, and adjusting cable tension on both sides. If your door also needs rollers or cables replaced, the visit runs longer, but we’ll tell you that on the phone before we schedule.
Yes. Our Carollton trucks carry a full range of torsion spring sizes and wire diameters, including Amarr-compatible specs for the most common residential door sizes in the area. For less common configurations, we can have the correct spring same-day or next morning from our supplier network. We’ll also show you the spring’s cycle rating and measurements before we install it.
If you’re not sure what you need, call us and we’ll help you identify it. The estimate is free, and it’s written.
Contact Us
If your Amarr garage door spring has broken, don’t force the opener, don’t try to wind a new one yourself, and don’t call someone who quotes you over the phone without seeing the part. Call Servo Garage Doors Carrollton at (817) 527-9864. We answer live, 24/7, and we’ll walk you through what you’re seeing, what it costs, and when we can be there. Free estimates, a written price before any work starts, and a documented record when we leave.
Written by Marcus Deller, Owner, Servo Garage Doors Carrollton at Servo Garage Doors Carrollton, serving Carrollton and nearby areas.